Add PoE variant with W5500 Ethernet and 802.3af power

- W5500 SPI Ethernet controller for wired connectivity
- Silvertel Ag9905MT PoE PD module (48V to 5V)
- RJ45 connector with integrated magnetics
- Higher camera resolution (1024x768 vs 800x600) using wired bandwidth
- WiFi fallback if Ethernet disconnected
- Separate BOM, pin mapping, ESPHome config
- 3D-printable enclosure (50x40mm, larger for RJ45)

poe-variant/BOM.csv

@@ -0,0 +1,54 @@
+Reference,Value,Footprint,JLCPCB_Part,Quantity,Description,Unit_Price_Est
+U3,ESP32-S3-WROOM-1-N16R8,RF_Module:ESP32-S3-WROOM-1,C2913202,1,WiFi+BLE MCU 16MB Flash 8MB PSRAM,$2.80
+U2,AMS1117-3.3,Package_TO_SOT_SMD:SOT-223-3_TabPin2,C6186,1,3.3V LDO Regulator 1A,$0.08
+U4,AP2112K-1.8,Package_TO_SOT_SMD:SOT-23-5,C51118,1,1.8V LDO camera DOVDD,$0.10
+U5,AP2112K-2.8,Package_TO_SOT_SMD:SOT-23-5,C51114,1,2.8V LDO camera AVDD,$0.10
+U6,SHT41,Sensirion_DFN-4-1EP_1.5x1.5mm,C2911456,1,Temp/Humidity I2C,$1.20
+U7,BH1750FVI,Package_SO:WSOF-6_1.4x1.7mm,C78960,1,Ambient Light I2C,$0.50
+U8,W5500,Package_QFP:LQFP-48_7x7mm_P0.5mm,C32843,1,SPI Ethernet Controller 10/100,$1.50
+U9,Ag9905MT,Module:Silvertel_Ag9905MT,N/A,1,802.3af PoE PD Module 5V/2A,$6.00
+J1,RJ45_PoE,Connector_RJ:RJ45_Amphenol_ARJM11C7,C911253,1,RJ45 with magnetics + PoE tabs,$1.20
+J2,FPC_24P_OV5640,Connector_FFC-FPC:Molex_503480-2400,C2856805,1,24-pin 0.5mm FPC camera,$0.20
+J3,LD2410C,Connector_PinHeader_1.27mm:PinHeader_1x05_P1.27mm,N/A,1,1.27mm header for LD2410C,$0.05
+J4,AM312_PIR,Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm,N/A,1,2.54mm header for AM312,$0.03
+Y1,25MHz,Oscillator_SMD:Crystal_SMD_3215-2Pin_3.2x1.5mm,C9002,1,25MHz crystal for W5500,$0.10
+D1,LED_Blue,LED_SMD:LED_0402_1005Metric,C2286,1,Blue status LED,$0.02
+D2,LED_Green,LED_SMD:LED_0402_1005Metric,C2286,1,Green Ethernet link LED,$0.02
+D3,LED_Yellow,LED_SMD:LED_0402_1005Metric,C2286,1,Yellow Ethernet activity LED,$0.02
+R1,1K,Resistor_SMD:R_0402_1005Metric,C11702,1,Status LED resistor,$0.01
+R2,10K,Resistor_SMD:R_0402_1005Metric,C25744,1,PIR pulldown,$0.01
+R3,4.7K,Resistor_SMD:R_0402_1005Metric,C25900,1,I2C SDA pull-up,$0.01
+R4,4.7K,Resistor_SMD:R_0402_1005Metric,C25900,1,I2C SCL pull-up,$0.01
+R5,12.1K,Resistor_SMD:R_0402_1005Metric,C25752,1,W5500 RES pin (sets modes),$0.01
+R6,1K,Resistor_SMD:R_0402_1005Metric,C11702,1,Ethernet link LED,$0.01
+R7,1K,Resistor_SMD:R_0402_1005Metric,C11702,1,Ethernet activity LED,$0.01
+R8,10K,Resistor_SMD:R_0402_1005Metric,C25744,1,W5500 INT pull-up,$0.01
+R9,10K,Resistor_SMD:R_0402_1005Metric,C25744,1,W5500 RST pull-up,$0.01
+C1,10uF,Capacitor_SMD:C_0805_2012Metric,C15850,1,LDO input,$0.02
+C2,22uF,Capacitor_SMD:C_0805_2012Metric,C45783,1,LDO output,$0.03
+C3-C5,100nF,Capacitor_SMD:C_0402_1005Metric,C1525,3,ESP32 decoupling,$0.03
+C6,10uF,Capacitor_SMD:C_0805_2012Metric,C15850,1,ESP32 bulk,$0.02
+C7,10uF,Capacitor_SMD:C_0805_2012Metric,C15850,1,Camera power,$0.02
+C8,100nF,Capacitor_SMD:C_0402_1005Metric,C1525,1,Camera decoupling,$0.01
+C9,10uF,Capacitor_SMD:C_0805_2012Metric,C15850,1,LD2410C decoupling,$0.02
+C10,100nF,Capacitor_SMD:C_0402_1005Metric,C1525,1,SHT41 decoupling,$0.01
+C11,100nF,Capacitor_SMD:C_0402_1005Metric,C1525,1,BH1750 decoupling,$0.01
+C12-C14,100nF,Capacitor_SMD:C_0402_1005Metric,C1525,3,W5500 decoupling,$0.03
+C15,10uF,Capacitor_SMD:C_0805_2012Metric,C15850,1,W5500 bulk,$0.02
+C16,22pF,Capacitor_SMD:C_0402_1005Metric,C1555,2,W5500 crystal load,$0.02
+C17,10uF,Capacitor_SMD:C_0805_2012Metric,C15850,1,PoE module output,$0.02
+C18,100uF,Capacitor_SMD:C_1206_3216Metric,C15008,1,PoE module bulk output,$0.05
+SW1,BOOT,Button_Switch_SMD:SW_SPST_PTS810,C116501,1,Boot button,$0.05
+SW2,RESET,Button_Switch_SMD:SW_SPST_PTS810,C116501,1,Reset button,$0.05
+H1-H2,MountingHole,MountingHole:MountingHole_2.2mm_M2_Pad,N/A,2,M2 mounting,$0.00
+,,,,,,
+,,,MODULES (plug-in),,,,
+MOD1,OV5640,Camera Module 5MP 120° wide-angle,N/A,1,24-pin FPC camera,$3.50
+MOD2,HLK-LD2410C,24GHz mmWave Radar Module,N/A,1,Presence radar,$2.50
+MOD3,AM312,Mini PIR Sensor Module,N/A,1,PIR sensor,$0.50
+,,,,,,
+,,,TOTAL PCB COMPONENTS,,~40,~$14.50
+,,,TOTAL WITH MODULES,,~43,~$21.00
+,,,PCB FABRICATION (5pcs),,,~$8.00
+,,,SMD ASSEMBLY (per board),,,~$15.00
+,,,TOTAL PER BOARD (assembled),,,"~$44.00"

poe-variant/DESIGN.md

@@ -0,0 +1,109 @@
+# Presence Sensor - PoE Variant
+
+Same sensors as the USB-C version, but powered and networked via Power over Ethernet (802.3af).
+
+## Key Differences from USB-C Version
+
+| Feature | USB-C Version | PoE Version |
+|---------|--------------|-------------|
+| Power | USB-C 5V | 802.3af PoE (48V → 5V) |
+| Network | WiFi only | Ethernet (wired) + WiFi fallback |
+| Connector | USB-C | RJ45 |
+| Extra chips | None | W5500 (Ethernet) + AG9905MT (PoE PD) |
+| Board size | 45x35mm | 50x40mm (RJ45 is bulky) |
+| Reliability | WiFi dependent | Wired, rock-solid |
+| Cost | ~$32 | ~$42 |
+
+## Why PoE is Better for Cameras
+
+- **No WiFi congestion** - camera streams are bandwidth-heavy
+- **Single cable** - power + data in one Ethernet run
+- **More reliable** - no WiFi dropouts
+- **Centralized power** - PoE switch manages all device power
+- **Remote reboot** - cycle PoE port to hard-reset device
+
+## New Components
+
+### W5500 Ethernet Controller
+- SPI interface to ESP32-S3
+- 10/100 Mbps Ethernet
+- Hardware TCP/IP stack (offloads ESP32)
+- QFP-48 package (7x7mm)
+- JLCPCB: C32843
+
+### RJ45 with Integrated Magnetics + PoE
+- HR911105A or equivalent
+- Includes PoE center-tap connections
+- Through-hole (adds height but very robust)
+
+### PoE PD Module - Silvertel Ag9905MT
+- IEEE 802.3af compliant (up to 13W)
+- 48V input → 5V/2A output
+- Tiny module: 16.5x14.5mm
+- Isolated, protected
+- Alternative: AG9905M-R or TI TPS2376 discrete
+
+### 25MHz Crystal Oscillator
+- Required by W5500
+- 3.2x2.5mm SMD package
+
+## GPIO Changes for PoE Variant
+
+| GPIO | USB-C Version | PoE Version |
+|------|--------------|-------------|
+| GPIO19 | USB D- | **Free** (no USB) |
+| GPIO20 | USB D+ | **Free** (no USB) |
+| GPIO33 | Free | **W5500 SPI MISO** |
+| GPIO34 | Free | **W5500 SPI MOSI** |
+| GPIO35 | Free | **W5500 SPI SCK** |
+| GPIO36 | Free | **W5500 SPI CS** |
+| GPIO37 | Free | **W5500 INT** |
+| GPIO42 | Free | **W5500 RST** |
+
+Camera, mmWave, PIR, I2C sensors - all unchanged.
+
+## Power Path
+
+```
+PoE Switch (48V)
+    │
+    ▼
+RJ45 Connector (center-taps)
+    │
+    ▼
+Ag9905MT PoE PD Module
+    │ (48V → 5V isolated)
+    ▼
+5V Rail ──→ LD2410C (direct)
+    │
+    ▼
+AMS1117-3.3
+    │
+    ▼
+3.3V Rail ──→ ESP32-S3, W5500, sensors, camera LDOs
+```
+
+## Power Budget (PoE)
+
+| Component | Voltage | Current |
+|-----------|---------|---------|
+| ESP32-S3 | 3.3V | 240mA |
+| W5500 | 3.3V | 132mA |
+| OV5640 | 2.8V+1.8V | 140mA |
+| LD2410C | 5V | 60mA |
+| AM312 + SHT41 + BH1750 | 3.3V | 3mA |
+| Ag9905MT overhead | - | ~50mA |
+| **Total from PoE** | 48V | **~180mA @ 48V (~8.6W)** |
+
+Well within 802.3af's 12.95W limit.
+
+## Board Layout Notes
+
+- RJ45 connector at bottom (cable exits down for wall mount)
+- Ag9905MT module near RJ45 (short high-voltage traces)
+- W5500 between RJ45 and ESP32 (short SPI traces)
+- Camera at top (unchanged)
+- mmWave on right (unchanged)
+- PIR on left (unchanged)
+- Sensors on left edge (unchanged)
+- Board slightly larger: 50x40mm to accommodate RJ45 jack height

poe-variant/PIN_MAPPING.md

@@ -0,0 +1,59 @@
+# ESP32-S3 Pin Mapping - PoE Presence Sensor
+
+## GPIO Assignments
+
+| GPIO | Function | Peripheral | Direction | Notes |
+|------|----------|-----------|-----------|-------|
+| GPIO0 | BOOT button | - | Input | Pull-up, hold low for bootloader |
+| GPIO1 | Camera D0 | OV5640 DVP | Input | Camera data bus |
+| GPIO2 | Camera D1 | OV5640 DVP | Input | Camera data bus |
+| GPIO3 | I2C SDA | SHT41 + BH1750 | Bidir | 4.7K pull-up |
+| GPIO4 | I2C SCL | SHT41 + BH1750 | Bidir | 4.7K pull-up |
+| GPIO5 | Camera D2 | OV5640 DVP | Input | Camera data bus |
+| GPIO6 | Camera D3 | OV5640 DVP | Input | Camera data bus |
+| GPIO7 | Camera D4 | OV5640 DVP | Input | Camera data bus |
+| GPIO8 | Camera D5 | OV5640 DVP | Input | Camera data bus |
+| GPIO9 | Camera D6 | OV5640 DVP | Input | Camera data bus |
+| GPIO10 | Camera D7 | OV5640 DVP | Input | Camera data bus |
+| GPIO11 | Camera XCLK | OV5640 | Output | 20MHz LEDC |
+| GPIO12 | Camera PCLK | OV5640 | Input | Pixel clock |
+| GPIO13 | Camera VSYNC | OV5640 | Input | Vertical sync |
+| GPIO14 | Camera HREF | OV5640 | Input | Horizontal ref |
+| GPIO15 | Camera SIOD | OV5640 SCCB | Bidir | Camera I2C data |
+| GPIO16 | Camera SIOC | OV5640 SCCB | Output | Camera I2C clock |
+| GPIO17 | mmWave UART TX | LD2410C RX | Output | 256000 baud |
+| GPIO18 | mmWave UART RX | LD2410C TX | Input | 256000 baud |
+| GPIO19 | Free | - | - | (was USB D-) |
+| GPIO20 | Free | - | - | (was USB D+) |
+| GPIO21 | Camera PWDN | OV5640 | Output | Power down |
+| GPIO33 | W5500 SPI MISO | Ethernet | Input | SPI data in |
+| GPIO34 | W5500 SPI MOSI | Ethernet | Output | SPI data out |
+| GPIO35 | W5500 SPI SCK | Ethernet | Output | SPI clock (25MHz max) |
+| GPIO36 | W5500 SPI CS | Ethernet | Output | SPI chip select |
+| GPIO37 | W5500 INT | Ethernet | Input | Interrupt (active low) |
+| GPIO38 | PIR output | AM312 | Input | Motion detect |
+| GPIO39 | mmWave OUT | LD2410C | Input | Presence output |
+| GPIO40 | Status LED | Blue LED | Output | Via 1K resistor |
+| GPIO41 | Camera RESET | OV5640 | Output | Active low |
+| GPIO42 | W5500 RST | Ethernet | Output | Active low |
+
+## SPI Bus (GPIO33-36) - W5500 Ethernet
+| Signal | GPIO | W5500 Pin |
+|--------|------|-----------|
+| MISO | GPIO33 | SO |
+| MOSI | GPIO34 | SI |
+| SCK | GPIO35 | SCLK |
+| CS | GPIO36 | SCSn |
+| INT | GPIO37 | INTn |
+| RST | GPIO42 | RSTn |
+
+## I2C Bus (GPIO3/GPIO4) - Sensors
+| Device | Address | Function |
+|--------|---------|----------|
+| SHT41 | 0x44 | Temperature + Humidity |
+| BH1750 | 0x23 | Ambient Light |
+
+## UART1 (GPIO17/GPIO18) - Radar
+| Device | Baud | Function |
+|--------|------|----------|
+| LD2410C | 256000 | mmWave presence |

poe-variant/enclosure-poe.scad

@@ -0,0 +1,133 @@
+// ============================================
+// Presence Sensor PoE - Wall-Mount Enclosure
+// Board: 50 x 40 mm (larger for RJ45 + PoE module)
+// ============================================
+
+pcb_w = 50;
+pcb_h = 40;
+pcb_t = 1.6;
+wall = 1.8;
+tolerance = 0.3;
+bottom_gap = 3;
+top_gap = 14;  // Extra height for RJ45 jack
+lid_lip = 1.5;
+
+inner_w = pcb_w + tolerance * 2;
+inner_h = pcb_h + tolerance * 2;
+inner_d = bottom_gap + pcb_t + top_gap;
+outer_w = inner_w + wall * 2;
+outer_h = inner_h + wall * 2;
+outer_d = inner_d + wall;
+
+post_d = 4.5;
+screw_d = 2.2;
+post_h = bottom_gap;
+
+// Component windows
+cam_hole_w = 10;
+cam_hole_h = 10;
+pir_hole_d = 10;
+light_hole_d = 4;
+rj45_w = 16;
+rj45_h = 14;
+
+module rounded_box(w, h, d, r) {
+    hull() {
+        translate([r, r, 0]) cylinder(h=d, r=r, $fn=20);
+        translate([w-r, r, 0]) cylinder(h=d, r=r, $fn=20);
+        translate([r, h-r, 0]) cylinder(h=d, r=r, $fn=20);
+        translate([w-r, h-r, 0]) cylinder(h=d, r=r, $fn=20);
+    }
+}
+
+module wall_mount_keyhole() {
+    cylinder(h=wall+2, d=7, $fn=24);
+    translate([0, -5, 0])
+        hull() {
+            cylinder(h=wall+2, d=4, $fn=24);
+            translate([0, 5, 0]) cylinder(h=wall+2, d=4, $fn=24);
+        }
+}
+
+module body() {
+    difference() {
+        rounded_box(outer_w, outer_h, outer_d, 3);
+        translate([wall, wall, wall])
+            rounded_box(inner_w, inner_h, inner_d + 1, 2);
+
+        // Camera window (top center)
+        translate([wall + tolerance + pcb_w/2 - cam_hole_w/2,
+                   wall + tolerance + pcb_h - 7,
+                   -1])
+            rounded_box(cam_hole_w, cam_hole_h, wall + 2, 2);
+
+        // PIR window (left)
+        translate([wall + tolerance + 12,
+                   wall + tolerance + pcb_h - 22,
+                   -1])
+            cylinder(h=wall+2, d=pir_hole_d, $fn=32);
+
+        // Light sensor window
+        translate([wall + tolerance + 24,
+                   wall + tolerance + pcb_h - 22,
+                   -1])
+            cylinder(h=wall+2, d=light_hole_d, $fn=32);
+
+        // RJ45 cutout (bottom edge)
+        translate([wall + tolerance + pcb_w/2 - rj45_w/2,
+                   -1,
+                   wall + bottom_gap - 1])
+            cube([rj45_w, wall + 2, rj45_h]);
+
+        // Ventilation slots (sides)
+        for (i = [0:3]) {
+            translate([-1, wall + 5 + i * 10, wall + bottom_gap + pcb_t + 2])
+                cube([wall + 2, 8, 1.5]);
+            translate([outer_w - wall - 1, wall + 5 + i * 10, wall + bottom_gap + pcb_t + 2])
+                cube([wall + 2, 8, 1.5]);
+        }
+
+        // mmWave slot (back)
+        translate([wall + tolerance + pcb_w - 10,
+                   wall + tolerance + 5,
+                   outer_d - wall - 0.5])
+            rounded_box(8, 36, wall + 1, 1);
+
+        // Wall mount keyholes (back)
+        translate([outer_w/2, outer_h * 0.3, outer_d - wall - 1])
+            wall_mount_keyhole();
+        translate([outer_w/2, outer_h * 0.7, outer_d - wall - 1])
+            wall_mount_keyhole();
+    }
+
+    // PCB support posts
+    for (pos = [[wall + tolerance + 2.5, wall + tolerance + 2.5],
+                [wall + tolerance + pcb_w - 2.5, wall + tolerance + 2.5],
+                [wall + tolerance + 2.5, wall + tolerance + pcb_h - 2.5],
+                [wall + tolerance + pcb_w - 2.5, wall + tolerance + pcb_h - 2.5]]) {
+        translate([pos[0], pos[1], wall])
+            difference() {
+                cylinder(h=post_h, d=post_d, $fn=20);
+                cylinder(h=post_h + 1, d=screw_d, $fn=20);
+            }
+    }
+}
+
+module lid() {
+    difference() {
+        union() {
+            rounded_box(outer_w, outer_h, wall, 3);
+            translate([wall - lid_lip/2, wall - lid_lip/2, wall])
+                rounded_box(inner_w + lid_lip, inner_h + lid_lip, 2, 2);
+        }
+        // LED windows
+        translate([wall + tolerance + 42, wall + tolerance + 30, -1])
+            cylinder(h=wall+2, d=2, $fn=16);
+        translate([wall + tolerance + 44, wall + tolerance + 30, -1])
+            cylinder(h=wall+2, d=2, $fn=16);
+    }
+}
+
+// Render
+body();
+translate([outer_w + 10, 0, 0]) lid();

poe-variant/esphome-presence-sensor-poe.yaml

@@ -0,0 +1,193 @@
+substitutions:
+  name: presence-sensor-poe
+  friendly_name: Presence Sensor PoE
+
+esphome:
+  name: ${name}
+  friendly_name: ${friendly_name}
+  platformio_options:
+    board_build.flash_mode: dio
+    board_build.arduino.memory_type: qio_opi
+
+esp32:
+  board: esp32-s3-devkitc-1
+  framework:
+    type: esp-idf
+  flash_size: 16MB
+
+psram:
+  mode: octal
+  speed: 80MHz
+
+logger:
+  level: INFO
+
+api:
+  encryption:
+    key: !secret api_key
+
+ota:
+  - platform: esphome
+    password: !secret ota_password
+
+# ==========================================
+# ETHERNET - W5500 SPI (primary network)
+# ==========================================
+ethernet:
+  type: W5500
+  clk_pin: GPIO35
+  mosi_pin: GPIO34
+  miso_pin: GPIO33
+  cs_pin: GPIO36
+  interrupt_pin: GPIO37
+  reset_pin: GPIO42
+  clock_speed: 25MHz
+
+# WiFi as fallback only (if Ethernet cable disconnected)
+wifi:
+  ssid: !secret wifi_ssid
+  password: !secret wifi_password
+  ap:
+    ssid: "${name}-fallback"
+    password: !secret fallback_password
+
+# ==========================================
+# I2C Bus - SHT41 + BH1750
+# ==========================================
+i2c:
+  sda: GPIO3
+  scl: GPIO4
+  scan: true
+  frequency: 400kHz
+
+# ==========================================
+# UART - LD2410C mmWave Radar
+# ==========================================
+uart:
+  id: uart_ld2410
+  tx_pin: GPIO17
+  rx_pin: GPIO18
+  baud_rate: 256000
+  parity: NONE
+  stop_bits: 1
+
+# ==========================================
+# Camera - OV5640 5MP
+# ==========================================
+esp32_camera:
+  name: Camera
+  external_clock:
+    pin: GPIO11
+    frequency: 20MHz
+  i2c_pins:
+    sda: GPIO15
+    scl: GPIO16
+  data_pins: [GPIO1, GPIO2, GPIO5, GPIO6, GPIO7, GPIO8, GPIO9, GPIO10]
+  vsync_pin: GPIO13
+  href_pin: GPIO14
+  pixel_clock_pin: GPIO12
+  power_down_pin: GPIO21
+  reset_pin: GPIO41
+  # PoE = wired = more bandwidth, can push higher quality
+  resolution: 1024x768
+  max_framerate: 15fps
+  idle_framerate: 0.5fps
+  jpeg_quality: 10
+  vertical_flip: false
+  horizontal_mirror: false
+
+esp32_camera_web_server:
+  - port: 8080
+    mode: stream
+
+# ==========================================
+# LD2410C mmWave Presence Radar
+# ==========================================
+ld2410:
+  uart_id: uart_ld2410
+  id: ld2410_radar
+
+binary_sensor:
+  - platform: ld2410
+    has_target:
+      name: Presence
+      id: ld2410_presence
+    has_moving_target:
+      name: Moving Target
+    has_still_target:
+      name: Still Target
+
+  - platform: gpio
+    pin:
+      number: GPIO38
+      mode: INPUT
+    name: Motion
+    id: pir_motion
+    device_class: motion
+    filters:
+      - delayed_off: 10s
+
+  - platform: template
+    name: Occupancy
+    device_class: occupancy
+    lambda: |-
+      if (id(pir_motion).state || id(ld2410_presence).state) {
+        return true;
+      }
+      return false;
+    filters:
+      - delayed_off: 30s
+
+sensor:
+  - platform: ld2410
+    moving_distance:
+      name: Moving Distance
+    still_distance:
+      name: Still Distance
+    moving_energy:
+      name: Moving Energy
+    still_energy:
+      name: Still Energy
+    detection_distance:
+      name: Detection Distance
+
+  - platform: sht4x
+    temperature:
+      name: Temperature
+      accuracy_decimals: 1
+      filters:
+        - offset: -1.5
+    humidity:
+      name: Humidity
+      accuracy_decimals: 1
+    address: 0x44
+    update_interval: 30s
+    heater_max_duty: 0.0
+
+  - platform: bh1750
+    name: Illuminance
+    address: 0x23
+    measurement_duration: 69
+    update_interval: 10s
+
+  - platform: uptime
+    name: Uptime
+
+light:
+  - platform: status_led
+    name: Status LED
+    pin: GPIO40
+
+button:
+  - platform: restart
+    name: Restart
+  - platform: factory_reset
+    name: Factory Reset
+    disabled_by_default: true
+
+text_sensor:
+  - platform: ethernet_info
+    ip_address:
+      name: IP Address
+  - platform: version
+    name: ESPHome Version

poe-variant/lid_only_poe.scad

@@ -0,0 +1,2 @@
+use <enclosure-poe.scad>;
+lid();